Pro-Seal 6006EX is an extra flexible, two-component pourable grade sealant. Specially designed for sealing traffic detector loops in both asphalt and concrete.
Traffic Detector Inductive Loop Sealant
EX = Extra Flexible
Pro-Seal 6006EX is an extra flexible, two-component pourable grade sealant. Specially designed for sealing traffic detector loops in both asphalt and concrete. Pro-Seal 6006EX fully encapsulates the loop wires for added protection. 6006EX is also an excellent sealant for embedding preformed detector loops.
Pro-Seal Advantages
|
|
|
|
|
|
|
|
Mixing
1. Remove lid and add the required amount of catalyst (Hardener). Remember to use less catalyst in the summer and more catalyst in the winter.
2. Mix for 30-45 seconds using a variable speed drill equipped with a mixing attachment. If mixing by hand, use a paint stir stick or other suitable device and mix for a minimum of three minutes.
Application Instructions:
1. Pour “mixed” Pro-Seal 6006 into loop slot, encapsulating loop wires.
2. Scrape any excess sealant off roadway with a squeegee. Curing: The amount of catalyst (hardener) used can be varied for a faster or slower cure. Consult Technical Data Sheet DLS-1 for cure times.
Packaging:
Pro-Seal 6006 is packaged in convenient 1 gallon cans, 5 gallon pails, and 55 gallon drums for use with pneumatic pump systems
Storage: Shelf life is one year in original unopened containers. Do not store above 100°F.
Specifications
| Color: | Brown |
| Viscosity: | 4800 cps (maximum) |
| Weight Per Gallon: | 12.0 lb/gal (minimum) |
| Specific Gravity: | 1.33-1.38 |
| Catalyst Required: | MEKP (Red) 2 tubes/gallon |
| Catalyzation Ratio: | 1% |
| Gel Time @ (77°F): | 13.0 to 18.0 Min.-ASTM C881 |
| Shore “D” Hardness | @ 60 Min. 15-20 @ 24 hours 45-50 |
| Elongation: | 30% (min)-ASTM D638 |
| Tensile Strength: | 500 psi (max)-ASTM D638 |
| Adhesion to Concrete: | 300 PSI-ASTM D3163-84 |
| Adhesion to Asphalt: | Excellent |
| Water Absorption: | 0.18%-ASTM D570 |
| Oil Absorption (No.3 Oil): | 0.02%-ASTM D570 |
| Gas Absorption: | 0.04%-ASTM D570 |
This product can only be shipped via ground transport.
DLS-1 Technical Data Sheet
For Pro-Seal 6006 & 6006EX
The proportion of catalyst to sealer is not very critical in obtaining a complete cure. The quantity of catalyst can be adjusted depending on climatic conditions. Use less catalyst in hot weather and more catalyst in cold weather. Each gallon of Pro-Seal is supplied with two (2) 1 ounce tubes of catalyst. Extra catalyst can be purchased separately. Use the chart below to determine the amount of catalyst to use.
Curing Time Matrix
| N/R=Not Recommended Ambient Temperature in °F | |||||||
| Tube(s) | 30°- 45° | 45°- 55° | 55°- 65° | 65°- 75° | 75°- 80° | 80°- 90° | +90° |
| Per Gallon | Time in Minuets | ||||||
| 1 | N/R | N/R | N/R | N/R | N/R | N/R | 12-18 |
| 2 | N/R | 30-35 | 25-30 | 20-25 | 15-20 | 10-15 | Under 10 |
| 3 | 20-25 | 15-20 | 10-15 | 7-10 | N/R | N/R | N/R |
Note: To thicken Pro-Seal for use on steep inclines dry sand may be added during the mixing process. Dry sand may be spread on top of Pro-Seal to make it instantly tack free. Sand is especially helpful for lead-ins across open lanes of traffic.
Use the coverage chart below to calculate the fill rate per gallon of Pro-Seal in various size saw cuts slots.
6006 Sealer Fill Matrix
| Saw Cut | Width | ||||
| Depth | 3/16″ | 1/4″ | 5/16″ | 3/8″ | 1/2″ |
| 1″ | 100′ | 80′ | 66′ | 53′ | 40′ |
| 1 1/2″ | 75′ | 53′ | 45′ | 36′ | 27′ |
| 2″ | 50′ | 40′ | 33′ | 26′ | 20′ |
| 3″ | 36′ | 27′ | 23′ | 18′ | 14′ |
